WorkWindow

Concrete Pouring Weather in Alton, IL: 10-Day Windows & Best Months

The concrete pouring season in Alton runs April through October — 7 months averaging at least 8 workable days by NOAA 1991–2020 normals. The single best month is August, averaging 24 days that clear every check — highs of 86°F, lows near 67°F, and a 22% daily rain chance. Below: today through day 10 against the label rules, then the year at a glance.

GOOD — every label check passes MARGINAL — one soft fail NO — hard fail or several soft

The rules this check uses

The Alton strip runs on these rows — bagged-mix consensus for DIY-scale work, ruled by the 48-hour freeze check. Structural pours answer to an engineer and ACI, not to this page.

Typical label thresholds for concrete pouring — the ruleset behind every Alton verdict above.
CheckThresholdWhy it matters
Air temperature 40–90°F — ideal 50–85°F The film (or mix) chemistry runs on temperature — both while you work and for the first hours after.
Overnight low ≥40°F during the first 48 h Curing continues after dark; the first night can undo a perfect afternoon.
Dry before no soaking (≥1.0") in the prior 24 h Checked backward from your start hour using the two look-back days in the forecast data.
Dry after <0.1" rain for 6 h after (12 h light rain after finishing still risks surface marks) The engine sums forecast rain hour by hour through the cure window for Alton.
Wind ≤20 mph (rapid surface drying up to 28 mph) Hot wind pulls bleed water out faster than the slab can handle.

Always follow your product label — formulas vary. The table above is the typical range across major manufacturers, not a promise about your can.

Best months for concrete pouring in Alton

Alton's calendar, scored: each month's days passing the temperature rules, discounted by that day's historical rain odds (NOAA 1991–2020). Not a forecast.
MonthAvg highAvg lowRain odds/dayWorkable days 
January 39°F 22°F 24% 0
February 44°F 25°F 26% 0
March 54°F 35°F 31% 0
April 66°F 45°F 35% 20
May 75°F 56°F 36% 20
June 84°F 66°F 28% 21
July 87°F 69°F 24% 24
August 86°F 67°F 22% 24
September 80°F 60°F 22% 23
October 68°F 48°F 25% 23
November 54°F 36°F 28% 4
December 44°F 27°F 26% 0

Figure 160 workable days a year in Alton, spread across April through October. Shoulder months turn on the overnight rule: an afternoon at 66°F passes, but the 40°F night floor is what actually opens the season in April. The Illinois table ranks every listed city by the same math.

Sealing the same driveway later? Sealcoating in Alton wants warmer nights (50°F+) than the pour did.

Source honesty: every monthly figure on this page is the 1991–2020 normal at Alton - Melvin Price L&D, Il Us, 4.1 km from Alton's center — your block's shade lines and wind exposure sit on top of that baseline. Scoring details are on the methodology page.

Alton by the numbers

Prep checklist

  1. Clear the 48-hour rule first: two nights over 40°F. April opens that door in Alton; January (22°F average lows) slams it.
  2. Nothing gets mixed until the site is staged — braced forms, compacted damp base, rinsed tools, a second pair of hands.
  3. Cut plastic sheeting and weight it at the pour's edge — Alton sees rain on 22% of August days, and the 6-hour rule doesn't negotiate.
  4. Mix to a low slump — thick oatmeal, not soup; extra water now is a weak surface forever.
  5. Timing beats muscle — screed wet, float at the dull stage, and never chase bleed water with a trowel.
  6. Edge and joint with an edger + float set — control joints every 2–3 slab-thicknesses in feet.
  7. Hold the moisture in (sheeting or misting); when October nights dip toward 48°F, a curing blanket is the difference.
  8. Keep feet off 24–48 hours and cars off a week; structural pours follow the engineer and ACI, full stop.

Gear that saves a window

Transparency note: gear links here become affiliate links only when the program is enabled — today they are plain references. See the affiliate disclosure.

FAQ

What temperature is too cold to pour concrete?

The line is a 40°F low inside the first 48 hours; an actual freeze (32°F) physically damages young concrete. Alton's January nights average 22°F — firmly out — while August nights hold near 67°F. Small pours only; structural work follows engineer/ACI specs.

Can you pour concrete before rain?

The engine wants 6 protected hours; light rain later actually feeds the cure. With 36% rain-day odds in May versus 22% in September, Alton's dry-season pours barely think about this rule and wet-season pours live by the radar. For small DIY pours; structural schedules follow ACI.

How long does concrete need to be protected from freezing?

Keep it above freezing for at least the first 48 hours (the engine calls any sub-40°F low in that window a NO). In Alton that rules out roughly January-adjacent months entirely and makes shoulder-season pours a two-night forecast decision. DIY scope; anything structural follows engineer/ACI cold-weather practice.

Is it OK to pour concrete in hot weather?

To a 90°F high, yes — with shade, cool mix water, a damp subgrade, and a dawn start. Above 90°F the surface sets while the core is plastic and shrinkage cracks map the slab. Alton averages 0 such days in July — rarely the binding constraint here.

How long before you can drive on new concrete?

A week before tires, 24–48 hours before feet — at August-typical Alton temperatures (86°F highs). When nights slide toward 22°F, add days: cure speed is temperature. Early loads print permanent marks; the bag's cure table wins every argument.

Best season for concrete work in Alton?

April through october — the months with 40°F+ nights, sub-90°F days, and manageable rain. August leads at 24 workable days; January bottoms out near 0.

Other projects in Alton

Concrete Pouring nearby

Guides

Climatology: NOAA 1991–2020 normals via ALTON - MELVIN PRICE L&D, IL US (4.1 km from Alton center, elevation 405 ft); live outlook by Open-Meteo.