Concrete Pouring Weather in Pasco, WA: 10-Day Windows & Best Months
Pasco gives you roughly 104 workable concrete pouring days a year, concentrated August through October. The single best month is September, averaging 27 days that clear every check — highs of 81°F, lows near 48°F, and a 11% daily rain chance. Below: the live 10-day check and Pasco's full month-by-month table.
GOOD — a clean label day MARGINAL — one borderline check NO — hard fail or stacked flags
The rules this check uses
Typical bagged-mix requirements for small DIY pours, scored against Pasco's forecast above. The 48-hour freeze rule dominates every other row; structural work follows engineer/ACI specs instead of this table.
| Check | Threshold | Why it matters |
|---|---|---|
| Air temperature | 40–90°F — ideal 50–85°F | DIY pours work from 40–90°F; 50–85°F is the sweet spot. |
| Overnight low | ≥40°F during the first 48 h | A low under 40°F inside the first 48 hours puts you in cold-weather concreting — not a DIY window. |
| Dry before | no soaking (≥1.0") in the prior 24 h | What fell before you start matters as much as what falls after — surfaces hold water invisibly. |
| Dry after | <0.1" rain for 6 h after (12 h light rain after finishing still risks surface marks) | The make-or-break window: rain here undoes the work, not just delays it. |
| Wind | ≤20 mph (rapid surface drying up to 28 mph) | Scored on the windiest working hour; the marginal band changes the method, not the day. |
Always follow your product label — formulas vary. Treat the table as the consensus range across brands — the label in your hand is the final word.
Best months for concrete pouring in Pasco
| Month | Avg high | Avg low | Rain odds/day | Workable days | |
|---|---|---|---|---|---|
| January | 41°F | 28°F | 32% | 0 | |
| February | 49°F | 28°F | 27% | 0 | |
| March | 59°F | 33°F | 25% | 0 | |
| April | 67°F | 38°F | 23% | 4 | |
| May | 76°F | 46°F | 22% | 24 | |
| June | 83°F | 53°F | 16% | 25 | |
| July | 92°F | 57°F | 7% | 5 | |
| August | 91°F | 56°F | 7% | 11 | |
| September | 81°F | 48°F | 11% | 27 | |
| October | 66°F | 38°F | 20% | 8 | |
| November | 50°F | 32°F | 29% | 0 | |
| December | 41°F | 27°F | 33% | 0 |
Figure 104 workable days a year in Pasco, spread across August through October. Shoulder months turn on the overnight rule: an afternoon at 91°F passes, but the 40°F night floor is what actually opens the season in August. Neighboring towns shift by a month or more — the Washington comparison shows where Pasco sits.
July here fails on heat, not rain: the average high of 92°F sits over the 90°F label ceiling, and 26 of 31 days typically top 90°F. Midsummer work moves to dawn or waits for September.
The rain odds swing hard across the year — 7% of days in August up to 33% in December. Season the plan accordingly: prep in the wet months, apply in the dry ones.
Sealing the same driveway later? Sealcoating in Pasco wants warmer nights (50°F+) than the pour did.
Climatology here is measured at Pasco Tri Cities Ap, Wa Us (2.3 km away). Treat the monthly numbers as the neighborhood average; a shaded north-side deck runs colder and damper than any of them. The exact formula lives in the methodology.
Pasco by the numbers
- Peak heat lands in July: 92°F average highs and 26 ninety-degree days.
- December bottoms the Pasco year: 41°F days, 27°F nights.
- Rain-day odds swing from 7% in August to 33% in December.
- Nights averaging 40°F+ run May through September.
- Annual workable concrete pouring days: about 104 of 365.
Prep checklist
- Clear the 48-hour rule first: two nights over 40°F. August opens that door in Pasco; December (27°F average lows) slams it.
- Stage everything before mixing: forms braced, base compacted and damp, tools rinsed, help booked.
- Cut plastic sheeting and weight it at the pour's edge — Pasco sees rain on 11% of September days, and the 6-hour rule doesn't negotiate.
- Resist the watery mix: it finishes easier today and dusts forever after. Low slump wins.
- Work the sequence: screed on the sheen, float as it dulls, and leave bleed water alone.
- Edge and joint with an edger + float set — control joints every 2–3 slab-thicknesses in feet.
- Hold the moisture in (sheeting or misting); when October nights dip toward 38°F, a curing blanket is the difference.
- Traffic schedule: feet at 24–48 hours, tires near day 7. Anything structural runs on engineer/ACI specs, not this checklist.
Gear that saves a window
Heads up: product links on this page may become affiliate links when the program is enabled. See the affiliate disclosure.
-
Concrete mix
An 80-lb bag yields about 0.6 cu ft — do the math twice.
-
Edger + float set
Rounded edges and a flat surface before it sets.
-
Curing blanket
Holds heat through cold nights in the critical 48 hours.
-
IR surface thermometer
Track slab temperature, not just the forecast.
FAQ
What temperature is too cold to pour concrete?
The line is a 40°F low inside the first 48 hours; an actual freeze (32°F) physically damages young concrete. Pasco's December nights average 27°F — firmly out — while September nights hold near 48°F. Small pours only; structural work follows engineer/ACI specs.
Can you pour concrete before rain?
The engine wants 6 protected hours; light rain later actually feeds the cure. With 33% rain-day odds in December versus 7% in August, Pasco's dry-season pours barely think about this rule and wet-season pours live by the radar. For small DIY pours; structural schedules follow ACI.
How long does concrete need to be protected from freezing?
Keep it above freezing for at least the first 48 hours (the engine calls any sub-40°F low in that window a NO). In Pasco that rules out roughly December-adjacent months entirely and makes shoulder-season pours a two-night forecast decision. DIY scope; anything structural follows engineer/ACI cold-weather practice.
Is it OK to pour concrete in hot weather?
To a 90°F high, yes — with shade, cool mix water, a damp subgrade, and a dawn start. Above 90°F the surface sets while the core is plastic and shrinkage cracks map the slab. Pasco averages 26 such days in July, which is why summer pours here move to first light.
How long before you can drive on new concrete?
A week before tires, 24–48 hours before feet — at September-typical Pasco temperatures (81°F highs). When nights slide toward 27°F, add days: cure speed is temperature. Early loads print permanent marks; the bag's cure table wins every argument.
Best season for concrete work in Pasco?
The table above says September, June and May: enough warmth for the 48-hour cure, short of the 90°F ceiling. For small DIY pours that's the whole answer; structural pours schedule to engineer/ACI requirements, not to a best-months chart.
Related
Other projects in Pasco
- Deck Staining in Pasco
- Exterior Painting in Pasco
- Driveway Sealing in Pasco
- Roof Coating in Pasco
- Lawn Seeding in Pasco
- All outdoor project weather in Pasco
Concrete Pouring nearby
- Kennewick, WA
- Yakima, WA
- Wenatchee, WA
- Spokane, WA
- Spokane Valley, WA
- Coeur d'Alene, ID
- Auburn, WA
- Gresham, OR
Guides
Climatology: NOAA 1991–2020 normals via PASCO TRI CITIES AP, WA US (2.3 km from Pasco center, elevation 407 ft); live outlook by Open-Meteo.